4 min readBy Artcolor
Cove lighting: how to design an LED cove that looks even
Cove lighting hides an LED strip in a ledge or recess and lights the ceiling or wall instead of the room. Where to put the strip, which strip and profile to use, and what to settle before the joinery is built.

Cove lighting is indirect light from an LED strip hidden in a ledge, recess or cove. You do not see the strip. You see the ceiling or wall it lights. Done well, the surface glows evenly and the room feels taller and calmer. Done badly, you see a hard bright band, a row of dots in a glossy ceiling, or one stretch that has turned yellow a year later.
The three common types of cove
- Ceiling cove (uplight). The strip sits on a ledge below the ceiling and lights the ceiling. It is the classic hotel lobby, corridor and living room cove.
- Wall cove (downlight or wall wash). The strip is hidden in a slot at the top of a wall, or under a bulkhead, and lights the wall below. This is close to wall wash lighting.
- Joinery cove. The strip is hidden under shelves, behind headboards, under counters or along stair treads. The same rules apply on a smaller scale.
1. Where to put the strip
Three things decide how the cove looks: what the strip faces, how far it is from the lit surface and whether anyone can see it.
- Point the light at the surface, not at the room. In a ceiling cove the light should land on the ceiling. A corner profile such as AL-1616D or AL-1919F tilts the strip, so more light lands where you want it.
- Distance changes the spread. The further the strip is from the ceiling or wall, the more the light spreads across it and the softer the edge. Close to the surface, the light is brighter at the start and fades faster.
- Keep it out of sight. Set the strip back behind the lip of the cove. Check the sight line from where people actually stand and sit, and from the top of a staircase or a mezzanine.
- Watch glossy surfaces. A gloss ceiling, stone or lacquer can mirror the strip. A dense strip and a diffuser cover help; see avoiding LED dots in reflections.
The cheapest way to settle all of this is a 1 m mock-up in the real cove detail, with the real finish, before the joinery is built.
2. Which LED strip for cove lighting
- Brightness. Compare strips by lumens per metre (lm/m), not watts. The same lm/m at a higher lm/W means less power and less heat. RayMax reaches up to 150 lm/W.
- Colour. Most hotel and residential coves are warm white, 2700K to 3000K. Every strip in one room should be one colour bin; ask for SDCM ≤3, or ≤2 on high-end work. See why two 3000K strips don't match.
- Dot-free light. Where the strip can be reflected, use a dense strip. Demini has 196 or 280 LEDs per metre and also carries 2700K and 6500K on one strip, so the cove can shift from warm to cool.
- Long runs. A cove can run tens of metres. One end feed reaches about 5 m on 12 V, 8–10 m on 24 V and further on 48 V; feeding both ends nearly doubles it. Ultra is made for long runs on 24 V and 48 V. See choosing LED strip voltage.
- Curves. For curved or round coves, Wave has an S-shaped board that bends sideways to a 30 mm radius.
3. Use an aluminium channel
A closed cove traps heat. An LED strip stuck straight onto timber or plasterboard runs hotter, and the hottest stretch fades and shifts colour first. An aluminium LED channel spreads that heat along its length and keeps the line straight. Read why LED strips fade in sealed coves before you close the cove in.
4. Corners, joins and control
- Corners and joins. Plan where the run turns and where it joins, and use the connector or soldered join that suits the strip. See how LED strip connectors work.
- Drivers. Put drivers where they can be reached later, not sealed inside the cove, and leave headroom on their rated power.
- Dimming. Most coves are dimmed. Choose the dimming protocol and the driver together; see dimming without flicker.
Checklist before the cove is built
- Section drawing of the cove, with the strip position and the sight lines.
- Finish of the lit surface: matt or gloss.
- Target lm/m and colour temperature, approved on a 1 m mock-up.
- Run lengths, feed points, cable routes and driver locations.
- Aluminium channel and cover for each run.
- Dimming protocol and control zones.
Cove lighting FAQ
What is cove lighting?
Cove lighting is indirect lighting from a light source hidden in a ledge, recess or cove, usually an LED strip. It lights the ceiling or wall, and that surface lights the room.
Which LED strip is best for cove lighting?
A 24 V strip with CRI >90, one colour bin per room and enough lm/m for the design, mounted in an aluminium channel. Use a dense strip where the cove can be seen in a glossy surface, and 24 V or 48 V for long runs.
Does an LED cove need an aluminium channel?
In most coves, yes. The channel draws heat away from the strip, keeps the line straight and gives a clean way to fit it. It matters most in closed coves and with higher W/m strips.
Planning a cove?
See how coves are used in hotel lighting, browse the LED strips and aluminium profiles, or send us the cove section and run lengths. We will suggest the strip, profile and feed points.
- Guides
- LED strip
- Cove lighting
