Skip to content
All posts

7 min readBy Artcolor

How to choose an LED strip channel (aluminium LED profile)

An LED strip channel, or LED profile, holds the strip, covers the LEDs and draws heat away. How to choose one by strip width, mounting, depth and cover.

Silver aluminium LED channel AL-1708, lit through an opal cover, with its end cap beside it

An LED channel is the aluminium housing an LED strip is fitted into. In the US it is usually called an LED channel, LED strip channel or aluminum channel. In the UK and Europe the same part is an LED profile or aluminium profile, and manufacturers call it an extrusion. All of these names mean one product.

What does an LED channel do?

An LED channel does four jobs: it keeps the strip straight, hides the LEDs, draws heat away and gives the strip a way to be fitted.

  • Keeps the line straight. The strip is stuck to the flat floor of the channel, so it follows a rigid line instead of the surface behind it.
  • Hides the LEDs. A push-in diffuser or opal cover softens the dots and hides the copper and the adhesive tape.
  • Draws heat away. Aluminium conducts heat away from the strip's board and spreads it over the whole channel, which gives it off to the air. That matters most where the surface behind is wood, plaster or plastic, or the cove is closed. See why LED strip fades in sealed coves.
  • Gives the strip a way to be fitted. It can be screwed or stuck on, recessed into a slot, plastered in, set in a corner or hung.

Do LED strip lights need a channel?

Not always. A channel is the usual choice when the line can be seen, when it has to be straight, or when the strip would otherwise be fixed straight to wood, plaster or plastic, which carry little heat away. The higher the strip's W/m, the more this matters.

1. Match the strip width

The inside width of the channel has to be wider than the strip's board. Each Artcolor profile is drawn for one strip width:

LED strip width Artcolor profiles Inside width
5 mm AL-0806, AL-0809 5.2 mm
8 mm 17 profiles: surface, recessed, corner, wall washer and plaster-in 8.6–16.2 mm
12 mm AL-2126, AL-5615, AL-2310, AL-3535E, AL-3535R 12.2–26.5 mm
16 mm AL-2312 20.6 mm

Check the strip width on its specification. Two strips can have the same LED chip and still be on different board widths.

2. Surface, recessed, plaster-in or corner: how is it mounted?

An LED channel can be surface-mounted, recessed into a slot, plastered in, fitted in a corner, hung as a pendant or set in the ground.

  • Surface: screwed or stuck onto a shelf, cabinet, wall or ceiling. 15 of the 25 profiles are surface-mounted, including the AL-1848 wall washer profile.
  • Recessed: set into a slot cut in the surface, with a lip that covers the edge of the cut. The recessed LED profiles AL-2507D, AL-2116 and AL-2515 need a 17–17.5 mm cut-out. The large AL-3535E needs 35 mm.
  • Plaster-in: AL-3612 and AL-5615 are plaster-in LED profiles. They are plastered into a 12.7 or 17 mm cut-out so the light line sits flush with the finished wall or ceiling. See plaster-in LED profiles for how they are fitted.
  • Corner: AL-1616D and AL-1919F are corner LED channels, shaped to sit in a corner.
  • Pendant: AL-3535R, 35 × 35 mm, hangs from the ceiling.
  • In-ground: AL-2126, 21.2 × 26 mm. No load or IP rating is published for it, so send us the floor detail first.
  • Wall washer: AL-1848, 18.2 × 48.6 mm, is a tall, surface-mounted profile.

Cross-section of the recessed AL-2116: 21.7 × 15 mm, an 8 mm strip on the floor of a 13.3 mm wide channel, with the cover on top

3. Depth: how far the cover sits from the LEDs

A deeper channel gives a more even line. Light from each LED spreads as it travels. The further the cover is from the LEDs, the more the light mixes before it reaches the cover.

  • Shallow channels suit tight spaces: AL-0806 is 6 mm high overall, AL-1608 7 mm.
  • Deep channels give the light more room to mix: AL-2016B is 21 mm high overall, AL-2016 19.6 mm.

LED density and the cover matter as well. A dense strip with a deep channel and an opal cover gives the smoothest line. Reflections in glass can still show the dots; see avoiding LED dots in reflections.

4. Choose the cover: clear, diffuser, opal or black

Each channel takes one of four covers. A softer cover hides the LED dots better but lets less light through.

Cover Light transmission Use
Clear 90–95 % Most light, where the strip itself is out of sight
Diffuser 70–80 % A softer line with more light than opal
Opal 65–75 % The most even line where it is seen
Black 50–55 % A dark line that looks black when it is off

Each cover pushes into the channel and comes with matching end caps.

5. Length, material and finish

  • Lengths: 1, 2.5, 3, 4, 5 or 6 m, cut to order.
  • Material: 6063-T5 aluminium, anodised.
  • Finishes: silver, black or white. Bronze, titanium gold, rose gold and silver grey are made to order.

Artcolor's 25 aluminium LED profiles

Artcolor offers 25 aluminium LED channels for 5, 8, 12 and 16 mm LED strips.

Model Mounting Size (W × H) Inside width Cut-out LED strip
AL-0806 Surface 8 × 6 mm 5.2 mm – 5 mm
AL-0809 Surface 7.6 × 9 mm 5.2 mm – 5 mm
AL-1010A Surface 10 × 10 mm 8.6 mm – 8 mm
AL-1215K Surface 12 × 15 mm 10.1 mm – 8 mm
AL-1608 Surface 16 × 7 mm 13.4 mm – 8 mm
AL-1613D Surface 16 × 13.1 mm 11.8 mm – 8 mm
AL-1616D Corner 16 × 16 mm 10.6 mm – 8 mm
AL-1708 Surface 17 × 8 mm 12.3 mm – 8 mm
AL-1716 Surface 17.1 × 15 mm 13.3 mm – 8 mm
AL-1716B Surface 17.1 × 15 mm 13.3 mm – 8 mm
AL-1824 Surface 18 × 15.8 mm 13 mm – 8 mm
AL-1848 Wall washer (Surface) 18.2 × 48.6 mm 12.1 mm – 8 mm
AL-1919F Corner 18 × 18 mm 12.3 mm – 8 mm
AL-2016 Surface 19.5 × 19.6 mm 16.2 mm – 8 mm
AL-2016B Surface 19.5 × 21 mm 16.2 mm – 8 mm
AL-2116 Recessed 21.7 × 15 mm 13.3 mm 17.1 mm 8 mm
AL-2507D Recessed 25 × 7.3 mm 12.3 mm 17 mm 8 mm
AL-2515 Recessed 24.7 × 15 mm 12.2 mm 17.5 mm 8 mm
AL-3612 Plaster-in 36.2 × 12.2 mm 10.3 mm 12.7 mm 8 mm
AL-2126 In-ground 21.2 × 26 mm 12.2 mm – 12 mm
AL-2310 Surface 23 × 9.7 mm 21 mm – 12 mm
AL-3535E Recessed 50 × 34.9 mm 24 mm 35 mm 12 mm
AL-3535R Pendant 35 × 35 mm 26.5 mm – 12 mm
AL-5615 Plaster-in 56 × 15 mm 14.1 mm 17 mm 12 mm
AL-2312 Surface 23.5 × 12.7 mm 20.6 mm – 16 mm

Every profile page has a cross-section drawing with the strip in place.

LED channel FAQ

Which LED channel for LED strip lights in a cove?

A surface or corner channel with an opal or diffuser cover, matched to the strip width. Corner channels tilt the light onto the ceiling. See how to design an LED cove.

Which LED channel for a display cabinet?

A slim channel with an opal cover: AL-0806 or AL-0809 for 5 mm strips, or one of the 17 profiles for 8 mm strips. See display cabinet lighting.

Aluminium or aluminum LED channel: is there a difference?

No. Aluminium is the British spelling and aluminum the American one. Both mean the same 6063-T5 aluminium extrusion.

Need a channel for a project?

Browse the aluminium LED profiles, or send us the strip model, the mounting detail and the lengths. We will suggest the profile and cover.

  • Guides
  • LED strip
  • LED channel

A new lighting-specification tip every day on LinkedIn.

Follow us on LinkedIn

Planning a project?

Tell us about your space — our team will recommend products or build them for you.

Contact sales