Skip to content
All posts

4 min readBy Artcolor

Display cabinet lighting: LED strips for showcases and vitrines

Good display cabinet lighting shows the object, not the light. Where to place LED strips in a showcase, how to avoid dots and glare in the glass, and which colour quality to ask for in retail, jewellery and museum cases.

A glass jewellery showcase on a bronze base, lit by a slim LED line along the top front edge

In a display cabinet the light should be invisible and the object should glow. That is harder than it sounds: the cabinet is small, made of glass, often closed, and seen from very close. A strip that looks fine in a ceiling cove can show every dot in a showcase.

This guide covers display case lighting for glass showcases, retail display cabinets, jewellery counters and museum vitrines.

1. Where to put the light

  • Top front edge, aimed back and down. The most common position. The light falls on the front of the objects and away from the viewer's eyes. In the photo above it is one slim line behind the top front glass.
  • Vertical lines in the front corners. These light the sides of tall objects and figures. A corner profile such as AL-1616D aims the strip into the case.
  • Shelf lighting, under each shelf. With glass shelves the light passes through to the shelf below. Use a slim profile on the front edge of each shelf.
  • Backlit back panel. A flexible LED sheet behind an opal or stone panel gives an even glowing background and silhouettes the objects.
  • Base light. A line along the base lights objects from below, used for glass, crystal and sculpture.

Keep the light out of the viewer's line of sight. If someone can look straight into the strip, it will glare.

2. No dots, no glare in the glass

The glass of the case and polished objects act as mirrors.

  • Dense strips. More LEDs per metre give a smoother line. SnipX has 120–240 LEDs per metre and Demini 196 or 280.
  • An opal cover and some depth. A deeper channel lets the light mix before it reaches the cover. See avoiding LED dots in reflections.
  • Exact lengths. Cabinet runs are short and fixed. SnipX can be cut at any LED, so the line runs right to the end of the case without a dark gap.

3. Colour quality

Objects in a showcase are seen from 30 cm, and buyers judge colour, so ask for more than "CRI 90".

  • Ra >90 is the starting point. SnipX, RayMax, PrimCore and Ultra are all CRI >90.
  • R9 for reds. Ask for R9 ≥50, and R9 ≥90 for retail and exhibition work. R9 decides how red stones, leather, textiles, skin tones and paintings look. See why CRI 90+ isn't the whole story.
  • Natural spectrum. ArmorCore uses SunLike LEDs at CRI >95, for artworks and high-end products.
  • One colour bin. Neighbouring cases must match. Ask for SDCM ≤3, or ≤2 on high-end work.

4. Colour temperature

Match the colour temperature to the objects and to the room. Warm white (2700K–3000K) is often used for gold, wood and leather; neutral or cool white for silver, platinum and diamonds. Mock it up with the real objects before you order. Where one case shows different collections, Demini carries 2700K and 6500K on one strip.

5. Heat, UV and drivers

  • Low W/m inside closed cases. A sealed case traps heat. Use an aluminium channel and keep the power per metre modest; see why LED strips fade in sealed coves.
  • Drivers outside the case. Put them in the plinth or a ventilated compartment where they can be reached.
  • UV and conservation. White LEDs put very little UV or infrared into the beam compared with halogen. Museum briefs still set light levels per object, so plan dimming and agree the lux target with the conservator.

6. Small sizes

Cabinet joinery leaves little room. For 5 mm strips, AL-0806 is 8 × 6 mm and AL-0809 7.6 × 9 mm. For 8 mm strips there are 17 profiles, including recessed and corner ones. See how to choose an LED strip channel.

Checklist for a display cabinet

  1. Case drawing with the light positions and the viewer's eye height.
  2. Objects and finishes: metal, stone, glass, textile, paper.
  3. Colour temperature, Ra, R9 and SDCM, approved with the real objects.
  4. Strip, profile and cover for each line, with exact lengths.
  5. Driver location, cable route and dimming.

Display cabinet lighting FAQ

What is the best LED strip for display cabinets?

A dense, CRI >90 strip with a high R9, in a slim aluminium channel with an opal cover, cut to the exact length of the case.

Where should LED strips go in a display cabinet?

Usually along the top front edge, aimed back and down at the objects, with vertical lines in the front corners and lines under glass shelves where needed.

Why do I see dots in my display cabinet glass?

The glass reflects each LED. Use a denser strip, an opal cover and a deeper channel, and move the strip out of the line of sight.

Lighting showcases?

See museum and gallery lighting and retail lighting, or send us the case drawings and what will be shown. We will suggest strips to compare on your objects.

  • Guides
  • LED strip
  • Display lighting

A new lighting-specification tip every day on LinkedIn.

Follow us on LinkedIn

Planning a project?

Tell us about your space — our team will recommend products or build them for you.

Contact sales