Skip to content
All posts

3 min readBy Artcolor

Can you cut LED strip lights? Cut points and cuttable LED strips

LED strips can be cut, but only at their marked cut points. Why the cut points are where they are, how far apart they sit on 12, 24 and 48 V strips, and what a cut-at-any-LED strip changes.

A dark red bar lit by warm lines of light around the counter, the curved ceiling and the seating

Yes. Most LED strips can be cut to length, but only at their marked cut points: short lines, often with a scissors symbol, across a pair of copper pads. Cut anywhere else and the section you cut through stops working.

Why a strip has cut points

An LED strip is a chain of short circuits, called segments, laid end to end. Each segment holds a few LEDs and the parts that limit their current, and runs on the strip's full voltage. The cut points are the joins between segments, so a strip can only be shortened by whole segments.

At the same LED density, the segment length follows the voltage: the higher the voltage, the more LEDs in each segment. SnipX is the exception: it is built so that every LED is a segment of its own. On Artcolor's 2835 strips:

Strip LEDs per segment Cut every
12 V, 120 LEDs/m (PrimCore) 3 25 mm
24 V, 120 LEDs/m (PrimCore) 6 50 mm
24 V, 240 LEDs/m (PrimCore) 6 25 mm
48 V, 168 LEDs/m (Ultra) 14 83.33 mm
24 V, 120–240 LEDs/m (SnipX) 1 4.17–8.33 mm

A longer segment means a coarser cut. That is the trade-off of 48 V: it keeps its brightness over long runs, but cannot be fitted as finely. See choosing 12 V, 24 V or 48 V.

Cut-at-any-LED strips

A cuttable LED strip in the narrow sense is one that can be cut after every LED. Artcolor's SnipX is made this way: 2835 LEDs at 120 to 240 per metre on 24 V, CRI > 90 and 1800K to 6500K, with a cut point every 4.17 to 8.33 mm. A run can be fitted to its space almost exactly, with no dark gap left at the end of a shelf or cove.

Other products have cut units of their own: Artcolor's COB strips cut every 25 or 50 mm, and its LED neon flex every 33.33 to 50 mm, depending on the size.

How to cut and reconnect an LED strip

  1. Switch off the power.
  2. Find the nearest cut mark at or below the length you need.
  3. Cut straight across the middle of the copper pads, so that each side keeps half a pad to connect to.
  4. Reconnect with a solderless clip connector made for that strip's width and pin count, or solder leads to the pads. See how LED strip connectors work.
  5. Restore the protection. A cut waterproof strip has lost its seal at the cut end; close it again with the matching end caps and sealant, or the finished run will not keep its IP rating.

Cutting LED strips FAQ

Can all LED strips be cut?

Most can, at their marked cut points. Some strips, such as many plug-in consumer kits with a built-in controller, should not be cut, and some sealed constructions are best cut and resealed by the maker. Check the product's datasheet.

What happens if I cut an LED strip in the wrong place?

The segment you cut through no longer forms a complete circuit, so its LEDs stay dark. The rest of the strip on the power side keeps working; you lose the length back to the previous cut point.

Can a cut LED strip be reconnected?

Yes. Join the pieces with a clip connector for that strip's width and pin count, or by soldering wires to the copper pads. Waterproof strips need their seal restored at the join.

What is a cuttable LED strip?

Every LED strip can be cut at its marks, but the term usually means a strip with very short cut units, such as a cut point after every LED. Artcolor's SnipX strips cut at every LED, every 4.17 to 8.33 mm.

Why do 24 V strips have longer cut sections than 12 V strips?

Each segment runs on the full strip voltage, so at the same LED density a 24 V segment holds more LEDs than a 12 V one: on Artcolor's 120 LEDs/m 2835 strips, six instead of three, so the cut points sit 50 mm apart instead of 25 mm.

Fitting strips to exact lengths?

Send us the run lengths and the layout, and we will suggest a strip whose cut points suit each run. Contact us, or browse the SnipX series.

  • Guides
  • LED strip
  • Installation

A new lighting-specification tip every day on LinkedIn.

Follow us on LinkedIn

Planning a project?

Tell us about your space — our team will recommend products or build them for you.

Contact sales