Skip to content
All posts

4 min readBy Artcolor

What is LED neon flex? Flexible LED neon lights explained

LED neon flex is a flexible LED light whose diffusing body turns the LEDs into one even line, like glass neon. How it differs from glass neon, how it bends, and where it is used.

A hotel lobby with continuous warm lines of light along the ceiling, the wall panelling and the base of the reception desk

LED neon flex is a flexible LED light in which a row of LEDs sits inside a diffusing body, usually of silicone. The body blends the LEDs into one continuous, even line of light, so it looks like glass neon tube, but it runs on low-voltage DC, is cut to length and bends on site. It is also called flexible LED neon or silicone neon flex.

LED neon flex and glass neon

Glass neon LED neon flex
Light source Gas in a glass tube LEDs in a flexible diffusing body
Power High-voltage transformer Low-voltage DC; 24 V on Artcolor's neon
Shaping Bent in the workshop by a glass bender Bent by hand on site, within its bend radius
Length Made to the drawing Cut to length at marked cut units
Handling Fragile glass Flexible; no glass to break

How LED neon bends

The direction a neon bends decides which shapes it can follow, so it is chosen with the artwork.

  • Top bend (also called vertical bending): the neon bends up and down, with the light facing out. Suits curves on a wall seen face on.
  • Side bend (horizontal bending): the neon bends sideways, along its flat side. Suits lettering and outlines traced on a surface.
  • 3D bend: the neon bends in every direction, for free shapes in space.
  • Round 360°: a round body that glows all the way around, for lines seen from every side.

Artcolor LED neon flex

Artcolor's LED neon flex comes in five series, all on 24 V DC with CRI > 90, a 75 mm minimum bend radius, runs of up to 5 m and a 3-year warranty:

Series Bend Sizes Protection
Aurora Top bend (T) or side bend (S) 10 × 10 to 20 × 20 mm IP65 / IP67
Flexa 3D 10 × 10 to 20 × 20 mm IP65 / IP67
Titan Top or side bend 16 × 16 and 12 × 25 mm IP68
Vanish Side bend 4 × 10 to 12 × 25 mm IP65 / IP67
Omni 3D, round 360° Ø 18 and Ø 23 mm IP65 / IP67

Every series comes in single colour from 2200K to 6500K; tunable white, RGB and RGBW depend on the series and size.

Where LED neon flex is used

  • Signs, logos and lettering in retail, hospitality and offices.
  • Outlines on façades, tracing the edges of a building after dark.
  • Joinery, bars and counters, where a soft line follows a curve.
  • Displays and installations, including round 360° neon hung in space.

Getting a good neon line

  1. Match the bend to the artwork. Check the tightest curve against the 75 mm minimum radius, and the bend direction against how the line is drawn.
  2. Cut only at the cut units. Each model has its own: 50 mm, 41.66 mm or 33.33 mm on Artcolor's neon, depending on the size.
  3. Plan the cable exits. The cable can leave from the front, the side or the bottom of the end, and the far end is closed with an end cap; choose them with the fixing details.
  4. Choose the protection for the place. IP65 / IP67 suits most outdoor façades; Titan is IP68. Connectors, end caps and drivers outdoors need their own protection.
  5. Mock it up. Light a sample length on site and look from where people will stand.

LED neon flex FAQ

What is LED neon flex made of?

A row of LEDs on a flexible circuit board inside a diffusing body, usually of silicone. The body spreads the light into an even line and protects the LEDs; the finished construction, with its end caps and cable exit, sets the IP rating.

Is LED neon flex better than glass neon?

It is easier to install and live with: it runs on low-voltage DC instead of a high-voltage transformer, has no glass to break, bends on site and is cut to length. Glass neon has its own look and craft, and is still chosen for that.

What is the difference between top bend and side bend neon?

Top bend (vertical bending) neon bends up and down with the light facing out; side bend (horizontal bending) neon bends sideways, along its flat side. Aurora is made in both versions, Vanish bends sideways, and Flexa and Omni bend in three dimensions.

Can LED neon flex be used outdoors?

Yes, in an outdoor-rated version. Artcolor's neon is rated IP65 / IP67, and the Titan series IP68. The connectors, end caps and the driver need their own protection outdoors.

How long can one run of LED neon be?

Up to 5 m per run on Artcolor's neon. Longer lines are made of several runs, each with its own power feed.

Planning a neon line?

Send us the artwork or drawing, the size and where it will be installed, and we will suggest a neon to sample. Contact us, or browse our LED neon flex.

  • Guides
  • LED neon
  • Architectural lighting

A new lighting-specification tip every day on LinkedIn.

Follow us on LinkedIn

Planning a project?

Tell us about your space — our team will recommend products or build them for you.

Contact sales